t ratio中文是什么意思

發音:

中文翻譯
造句

統計系數與標準誤差比率

t 中世紀羅馬數字的160。
ratio n. (pl. ratios) 1.比，比率，比值；比例 ...
as ratio 聯想感覺比
ratio n. (pl. ratios) 1.比，比率，比值；比例；系數。 2.【經濟學】復本位制中金銀的法定比價。 the ratio 3:2 (讀作 the ratio of three to two )3對2之比。 arithmetical ratio 公差，算術比。 direct ratio 正比。 inverse [reciprocal] ratio反比。 current ratio 電流比，電流變換系數。 nutritive ratio 營養率。 vt. 1.用比例方式表達；求出…的比值；使…成比例。 2.將(相片)按比例放大或縮小。
ratio t 統計系數與標準誤差比率
contact ratio and overlap ratio 齒輪重合度; 重合度
draw ratio, extension ratio 拉伸比
justification ratio (stuffing ratio) 碼速調整比（塞入比）
light ratio = magnitude ratio 光比
ratio of two ratio estimators 兩個比率估計量的比率
speed ratio, transmission ratio 傳動比
temperatureefficiency ratio (t-e ratio) 溫度效率比
transmission ratio, speed ratio 傳動比
a ect ratio 長寬比; 展弦比; 縱橫比
a orption ratio 吸收系數
abortion ratio 流產率
abrasion ratio 磨耗率
absorbance ratio 吸光度比值; 吸收度比值
absorption ratio 飽和系數; 吸收比; 吸收率; 吸收系數
absorptivityemissivity ratio 吸收發射比
abundance ratio 存在比（物理）; 豐度比; 含量比例
aca ratio 調節性集合/調節比率
acceleration ratio 加速比; 加速度比
accelerator ratio 促進劑比率; 促進劑用量比率
accessibility ratio 可及性比

"查查詞典"手機版

千萬人都在用的超大詞匯詞典翻譯APP

例句與用法

Theory deduce , experimentation and finite element analysis ( fea for short ) are carried out on b / t ratio of t - section steel
本文從理論分析、試驗研究、有限元計算三方面研究了剖分t型鋼腹板局部屈曲及寬厚比限值。
( 3 ) cu amino acid chelate promoted spleen growth in experiment 21 - 28d , thymus " degeneration were decreased and growth of spleen were promoted by supplemental cu in diet in cu - deficient mice . ( 4 ) cu - met promoted t lymphopoiesis more efficiently , anae + t ratio and t lymphopoiesis were increased by dietary supplemental copper
( 3 )氨基酸螯合銅能夠促進添加銅21天- 28天小鼠的脾臟發育，給缺銅小鼠飼糧添加銅能顯著減緩小鼠胸腺退化和促進脾臟發育。
Theory analysis in this paper pointed out that the flexural - torsional buckling is the usual form of t - section steel . so the slenderness ratio of flexural - torsional buckling should be used when people give out the b / t ratio by the " equal stability " conception . initial stress , defects and tangent modulus are include in the deduce of the paper to get a rational b / t ratio
通過理論分析指出軸心受力剖分t型鋼整體失穩以彎扭屈曲為主，所以在運用“等穩定”方法確定腹板寬厚比限值時應與桿件的扭轉長細比“掛鉤” ，并以此為出發點考慮殘余應力、初始缺陷，應用切線模量推導出了較為合理的腹板寬厚比限值公式。